The only Argentine manufacturer of certified dielectric mats — IRAM License in force
Verkom
Electrical safety · Macker

Dielectric insulating mats, three-layer and single-layer

We are the only Argentine manufacturer of dielectric mats with a current IRAM License for classes 0 to 4, to EN 61111:2010. Two constructions for two levels of use: three-layer for permanent work and heavy traffic, single-layer for occasional use.

Macker dielectric mat on a roll
EN 61111:2010Standard for dielectric insulating mats
IRAM License in forceDC-P-V56-001,1 (C3) · classes 0 to 4

Choose your mat

The class is chosen by the voltage of the installation you will work on. Each class has its own color, set by the standard.

All
By construction
ClassCodeWorking voltage · ACWorking voltage · DCTestWhere it is used
Class 0AD01,000 V1,500 V5,000 VIndustrial low voltage · switchboards · EV workshopsView datasheet
Class 0MC01,000 V1,500 V5,000 VIndustrial low voltage · switchboards · EV workshopsView datasheet
Class 1AD17,500 V11,250 V10,000 VMedium voltageView datasheet
Class 2AD217,000 V25,500 V20,000 VMedium-voltage installationsView datasheet
Class 2MC217,000 V25,500 V20,000 VMedium-voltage installationsView datasheet
Class 3AD326,500 V39,750 V30,000 VHigher electrical demandsView datasheet
Class 4AD436,000 V54,000 V40,000 VHigh voltage and high riskView datasheet
Working voltage

The maximum voltage of the installation the mat protects against.

Test

The test voltage, well above the working voltage. It is applied to a standard test piece from every production batch.

The three-layer mat is made in all five classes.

The single-layer mat, in class 0 and class 2.

Three-layer or single-layer

Both meet the standard. What changes is the construction and, with it, the use they are designed for. The three-layer mat is made in all five classes; the single-layer mat, in class 0 and class 2.

Cross-section of the three-layer mat showing its three layers
Three-layer construction

For permanent work and heavy traffic

Non-slip top layerWorking surface. Color according to class.
High dielectric strength coreThe insulating layer. It sets the class and the working voltage.
Protective baseProtects the core from the floor and from abrasion.

Three layers vulcanized into a single piece. The insulating core is protected above and below, so the mat withstands continuous traffic without losing thickness or insulating properties.

Usepermanent installation in front of energized switchboards and switchgear
Formatson a roll, 600 to 1000 mm wide, length to order · individual mats from 600 × 1000 mm
Includescarrying bag. Plastic profiles and screws to fix it to the floor, free of charge
Recommendedby inspection bodies for heavy-duty use
01234
Single-layer mat with its box and carrying bag
Single-layer construction

For occasional use and frequent moving

A single insulating layerNon-slip surface. Color according to class.

A single vulcanized layer, lighter and easier to carry. It passes the same EN 61111:2010 tests as the three-layer mat. Made in class 0 and class 2.

Useoccasional switching, maintenance and work away from a fixed station
Formatindividual 600 × 1000 mm
Includesbox and carrying bag in the class color
Advantagelightweight; rolls out and stores away in seconds
02
Flame retardancyTested to the standard
Non-slip surfaceDesigned for continuous technical traffic
Resistance to oils and acidsTested to the standard
Accelerated agingDimensional stability over time
Electric vehicle service bay with the mat installed
New use

Service bays for electric and hybrid vehicles

The high-voltage systems of an electric or hybrid vehicle run at 200 to 800 volts DC. Every time the service disconnect is pulled, the traction battery is opened or the orange cables are worked on, the technician is exposed.

Manufacturers' service manuals require the work bay to have a certified insulating floor, and dealer-network certification audits check for it.

Class 0 covers up to 1,500 V DC: the class for a high-voltage service bay
Three-layer for a fixed bay, with profiles that hold it to the floor
Single-layer for workshops that need to roll it out and put it away
IRAM mark is what the auditor looks for in the product marking

Why a mat and not just footwear and gloves

It is the difference between personal protection and collective protection.

The footwear blind spotA metal chip, a strand of copper wire or a screw on the floor can puncture or bridge a dielectric sole without the worker noticing. The mat does not depend on the condition of each person's footwear.
It protects everyone, not just one personA correctly sized mat protects anyone who operates in or passes through the area, without relying on each person checking their equipment before going in.
It backs up your auditInspections by the ART (occupational risk insurer) and industrial safety audits require certified physical barriers in front of energized switchboards. An IRAM-marked mat documents that due diligence.

Legal framework in Argentina. Health and Safety Law 19,587 and its Decree 351/79 (article 95 and annex VI) refer to the regulations of the Argentine Electrotechnical Association. SRT Resolution 3068/14 approves the rules for live low-voltage work up to 1,000 V, including physical barriers in front of switchboards, cabinets and motor control centers. The product also meets EN 61111:2010 and carries the IRAM mark and the S symbol.

Use, inspection and care

The mat is a piece of safety equipment: its condition is checked, not assumed.

Before each use

Visual inspection of both faces: cuts, cracks, punctures
Check that the class matches the installation voltage
Replace immediately if the mat has taken an actual discharge

Care and storage

Store flat, without compressing or folding, away from heat, sunlight and ozone
Use between −25 °C and 55 °C
Avoid chemicals, hydrocarbons, solvents, acids and strong alkalis
Dry at no more than 65 °C

Which class and construction do you need?

Send us these details and we will recommend the right mat, with its datasheet and certificate.

Installation voltageThe maximum voltage you will be working at
Type of useFixed station in front of a switchboard, or occasional switching
Surface to coverWidth of the switchboard front or of the bay
FasteningLoose, on a roll, or fixed to the floor with profiles